rriker

About

Username
rriker
Joined
Visits
0
Last Active
Roles
Member
Points
3
Badges
0

Comments

  • Simple, a switch that connects to endpoints (PCs) together on a common VLAN, as depicted in your picture, the switch would learn the MACs of PC1 and PC2. The CAM or MAC Address table would get populated with a MAC to Port binding, the port that lear…
  • This is a very easy solution. Use 1 EIGRP ASN for both DMVPN clouds, on tunnel 20 use the "delay 1000" option to be less preferred than tunnel 10. If tunnel 10 goes down, Tunnel 20 will take over based on EIGRP Feasible sucessor. When Tunnel 10 come…
  • I concur on this as well. I would have explained it the same way and then demo'd the variations.
  • Typically you are going to call an ACL to match the traffic source and type. ip access-list standard PBR permit source/length route-map PBR match address PBR set next hop x.x.x.x   Beyond that, there add'l options like verify reachabil…
  • I can't speak to the rack rentals as I don't use them. I have configured all IGPs leveraging all the different L2 VPN variations, AToM, VPLS, H-VPLS with no issues using the CSR. It could be that the CSRs need to be deleted and re-built. I have that…
  • I don't believe secondary addressing is supported on anything except Ethernet interfaces.
  • Show frame-relay map will show you what is configured and working. Sent from Yahoo Mail on Android On Wed, Jan 4, 2017 at 10:48 AM, Rob Riker wrote: I believe it is saying you configured that mapping already.  Sent from Yahoo Mail on …
  • I believe it is saying you configured that mapping already.  Sent from Yahoo Mail on Android On Wed, Jan 4, 2017 at 10:11 AM, major133 wrote: hi everyome   This is frame-relay topology , and this is my configurations:-   R2(…
  • The lab specifically doesn't use SecureCRT, it uses single session Putty. You click on an device icon and up pops a putty session for it. No tabs, no send commands to all.  On Monday, November 21, 2016 1:02 PM, frankie wrote: Does …
  • Broad overview of what you asked about. You can research more on your own. -rfc - request for comment - the standards that protocols are built from  -cisco tac - TAC - technical assistance center - Cisco's network helpdesk -vsiminar - vSeminar…
  • Unet does what GNS3 did, providing that connection visually, you can do this as well in ESXi. I normally will connect 10 routers in GNS3 to a L2 switch and then configure 802.1Q subinterfaces so that each router is a router on a stick. This is how t…
  • To my knowledge, ESXi will not run a qcow image. VIRL will and so will Unet, ESXi needs an OVA/OVF. I have read blog posts that walk you thorugh converting the qcow image to an OVA but I haven't personally done it. If you have purchased VIRL, then y…
  • Simple answer is the VLAN numbers space in the dot1q header is 12 bits. So the biggest value 12 bits can be is 4096. I didnt watch the video so i dont know if Keith mentioned that or not. The thing to remember is that bridge priority doesnt have any…
  • Look at it from the perspective of ACLs. Standard ACLs match on IP only, which encompasses ICMP, TCP, UDP, GRE, OSPF, EIGRP etc. Extended ACLs match on IP, TCP, UDP, ICMP etc, so you can be much more specific as to what type of traffic you want to m…
  • I've ran into that as well. It appears as though the demo license on the XR boxes do have a shelf life. I have had to re-deploy XRv boxes to get that working. The other thing to check, not shown in your output, is the license boot level on the other…
  • I haven't tried that type of deployment personally. Although, you will probably have to bridge the NIC on the server to the VM nets in workstation to get that working. then map the NIC on the CSR to the VMnet. It's a bit of a setup but pretty easy f…
  • I dont use an unmanaged switch with VIRL. I use a IOSvL2 switch and setup the ports with trunks. I havent had any problems. It does depend on what your testing. Sent from my Sprint Samsung Galaxy® Note 4. -------- Original message ---…
  • Yes there is. You can use TFTP to download the IOS image as long as you have IP reachability to the router/switch. I recommend you download TFTPd32 and install that. Then you'll be able copy the IOS image over the network to your PC. There is some c…
    in ios download Comment by rriker July 2016
  • should I study and spend time on ATM and Frame-Relay also ?    I am not aware of FR or ATM being on the exam. The blueprint for EDGE doesn't say anything about those specific WAN types. I am also preparing for NP SP and I haven't studied for the…
  • To begin with a CCNP level of understanding. You don't need to have taken or passed the exams (most do) but at least have the understanding and the ability to configure them. If you have covered that you know Core Layer 2/STP/Security/RIP/EIGRP/OS…
  • To be more specific, clock rate is done on the DCE side of a connection. The clock rate specifies how fast that particular interface can send data at. 64000 means that you can send 64,000 bits per second. Bandwidth is a relative to the interface and…
  • OK, so you want a tower style server. I use eBay here in the US to buy servers, but i get rack mount as I have a 20U rack in my basement. Good luck to you. This is an option: Dell PowerEdge T410 2 x SIX CORE XEON X5650 CPU 64GB RAM RAID Tower S…
  • I can tell you without a doubt that the X5560 will support and run without issue the CSR1000v, ASAv, PANOSv, BIGIP, ISE, ACS, vCenter Server Appliance, VIRL, Unetlab, IOS XRv. I have installed and ran all of the above platforms and tested features o…
  • I am running 2 IBM servers that I bought off of eBay a couple years ago. Both have Intel X5560 Quad Core processors. I have no issues running the INE topologies or anything I dream up as I test features out. I use 1 server for VIRL and 1 VM so I can…
  • You will get 1 piece of paper and pens/pencils. Each pod has that available. That piece of paper has your login info on it. You have the option to bring pen/pencils into the lab, but the proctor has to approve it. DON'T sneak things past, your askin…
  • A active  U update r reply from query Sent from my Sprint Samsung Galaxy® Note 4. -------- Original message -------- From: major133 Date: 4/16/16 6:19 PM (GMT-06:00) To: [email protected] Subject: [ccnp] question about eigrp Co…
  • Nope, you cant re certify an expired certification. Pass the written in any track and recertify all certifications, not sure about specialist exams, i know for sure with career certification. Sent from my Sprint Samsung Galaxy® Note 4. …
  • I don't use that method to use IOS XRv. Since it's giving you an ASN number, I would issue: sh run router bgp and see what is already configured.  You seem to already have BGP AS 1 configured, see below: RP/0/0/CPU0:XR2(config)#router bgp 1 …
    in IOS XR BGP Comment by rriker April 2016
  • I have been using VIRL for quite sometime now and have found it to be very useful. There are a few things it doesn't do well with, 802.1Q Tunneling, SPAN, etc. If you want to use that I would encourage it. I currently run both CSRs and VIRL at the s…
    in CCNP Lab Comment by rriker April 2016
  • Since you asked, and I have had several customer issue tickets about this recently, also involved TAC on a few issues, here is basically what's going on. The outputs are a bit skewed but they are a good indication of utilization. Now mind you, these…