test call from pstn to r3 , r3 to pstn

When I use the commnad "incoming called number " and try to dial to R3 I get a busy signal. When I take the command out I get another dial tone and then I dial the ext. and the phone rings. Why is that? I thought the command will the second dial tone.. 

Why when I configure DHCP on R3 I get a message stating Duplicate Address for 177.3.71.1 with some type of MAC address. Support tells me its a configuration problem  and they dont support it.. This is the second time that this happened to me..This is really getting old to me.. I need some type of help!!!!!!!!!!

 

 

Comments

  • Please post your coniguration on the forum; So far, it looks like the DID number is not assigned to any ephone-dn or internal dial-peers.

    Petr






    ----- Original Message -----
    From: "cagiva24" <[email protected]>
    Sent: Tue, January 13, 2009 16:01
    Subject: [CCIE Voice] test call from pstn to r3 , r3 to pstn


    When I use the commnad "incoming called number " and try to dial to R3 I get a busy signal. When I take the command out I get another dial tone and then I dial the ext. and the phone rings. Why is that? I thought the command will the second dial tone.. 

    Why when I configure DHCP on R3 I get a message stating Duplicate Address for 177.3.71.1 with some type of MAC address. Support tells me its a configuration problem  and they dont support it.. This is the second time that this happened to me..This is really getting old to me.. I need some type of help!!!!!!!!!!

     

     



    --
    View this message online at: http://ieoc.com/forums/p/4696/15250.aspx#15250
    --
    Internetwork Expert - The Industry Leader in CCIE Preparation

    http://www.internetworkexpert.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx
    <!>

  • isdn switch-type primary-net5

    controller e1 1/0
    framing crc4
    linecode hdb3
    pri-group time-slot 1-3

    interface serial 1/0:15
    isdn outgoing dispaly-ie

    dial-peer voice 999 pots
    incoming called-number .
    port 1/0:15
    direct-in-dial


    telephony-service
    max-dn 16
    max-ephone 4
    dial-patterne 1 273723... extenth 4
    time-zone 21
    dn-webedit
    ip source address 182.1.1.1 port 200
    time-webedt
    web admin system admin password cisco
    system message CME

    ip http server

     

    Your help is really appriciated

  • EPHONE 1
    MAC 0200.4c4f.4f04
    BUTTON 1:1 2:2
    PIN 12345
    SPEED-DIAL 1 3002

    EPHONE 2
    MAC 0200.4C4F.4F02
    BUTTON 1O3,4 2:5
    SPEED-DIAL 1 3001
    PIN 12345



  • Hmm in your configuration the dilaplan pattern is 273723... while it should be 27373...
    Is that the intended configuration? Also, can you provide "debug isdn q931" and "debug voic dialpeer all" output when dialing from the PSTN phone to 27273001?

    Petr



    ----- Original Message -----
    From: "cagiva24" <[email protected]>
    Sent: Tue, January 13, 2009 18:31
    Subject: Re: [CCIE Voice] test call from pstn to r3 , r3 to pstn


    isdn switch-type primary-net5

    controller e1 1/0
    framing crc4
    linecode hdb3
    pri-group time-slot 1-3

    interface serial 1/0:15
    isdn outgoing dispaly-ie

    dial-peer voice 999 pots
    incoming called-number .
    port 1/0:15
    direct-in-dial


    telephony-service
    max-dn 16
    max-ephone 4
    dial-patterne 1 273723... extenth 4
    time-zone 21
    dn-webedit
    ip source address 182.1.1.1 port 200
    time-webedt
    web admin system admin password cisco
    system message CME

    ip http server

     

    Your help is really appriciated



    --
    View this message online at: http://ieoc.com/forums/p/4696/15274.aspx#15274
    --
    Internetwork Expert - The Industry Leader in CCIE Preparation

    http://www.internetworkexpert.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx
    <!>

  • I have a lab session tonight. I will give it another try. thanks

  • That did it thanks a million. I also having an issue with the Cisco Comminicator connecting to the R3s TFTP. any ideas? thanks

Sign In or Register to comment.