cannot get terminal server config to work

I am trying to set up a 2851 router with an NM-32A network module and ios v. 15.1.4T and i cannot get this to work and I know I must be doing something wromg.

I have given the 2851 an IP address of 10.0.0.81/16 pm G0/0 and an IP address of 192.168.0.1/24 on L0

 

Where am I going wrong?  When I do a sh Lines the output is what I would expect.

Router#sh lin

Router#sh line 

   Tty Line Typ     Tx/Rx    A Modem  Roty AccO AccI  Uses  Noise Overruns  Int

      0    0 CTY              -    -      -    -    -     0      0    0/0      -

      1    1 AUX   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/0   66 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/1   67 TTY   9600/9600  -    -      -    -    -     0      1    0/0      -

    1/2   68 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/3   69 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/4   70 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/5   71 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/6   72 TTY   9600/9600  -    -      -    -    -     0      4    1/0      -

    1/7   73 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/8   74 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    1/9   75 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/10   76 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/11   77 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/12   78 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/13   79 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/14   80 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/15   81 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/16   82 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/17   83 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/18   84 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/19   85 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/20   86 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/21   87 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/22   88 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/23   89 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/24   90 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/25   91 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/26   92 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/27   93 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/28   94 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/29   95 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/30   96 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

   1/31   97 TTY   9600/9600  -    -      -    -    -     0      0    0/0      -

    514  514 VTY              -    -      -    -    -     1      0    0/0      -

*   515  515 VTY              -    -      -    -    -     1      0    0/0      -

    516  516 VTY              -    -      -    -    -     0      0    0/0      -

    517  517 VTY              -    -      -    -    -     0      0    0/0      -

    518  518 VTY              -    -      -    -    -     0      0    0/0      -

 

Line(s) not in async mode -or- with no hardware support: 

2-65, 98-513

 

Router#

 

in fact here is sh tech output:

Router#sh tech

 

------------------ show version ------------------

 

 

Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2012 by Cisco Systems, Inc.

Compiled Tue 20-Mar-12 18:13 by prod_rel_team

 

ROM: System Bootstrap, Version 12.4(13r)T5, RELEASE SOFTWARE (fc1)

 

Router uptime is 1 hour, 18 minutes

System returned to ROM by reload at 04:49:59 UTC Tue Sep 20 2016

System image file is "flash:c2800nm-ipvoicek9-mz.151-4.M4.bin"

Last reload type: Normal Reload

 

 

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

 

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

 

If you require further assistance please contact us by sending email to

export@cisco.com.

 

Cisco 2851 (revision 1.0) with 776192K/10240K bytes of memory.

Processor board ID FTX1118A3AY

2 Gigabit Ethernet interfaces

32 terminal lines

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

250368K bytes of ATA CompactFlash (Read/Write)

 

 

License Info:

 

License UDI:

 

-------------------------------------------------

Device#   PID                   SN

-------------------------------------------------

*0        CISCO2851             FTX1118A3AY     

 

 

 

Configuration register is 0x2102

 

 

------------------ show running-config ------------------

 

 

Building configuration...

 

 

Current configuration : 1119 bytes

!

! Last configuration change at 05:04:11 UTC Tue Sep 20 2016

version 15.1

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

!

enable password <removed>

!

no aaa new-model

!

dot11 syslog

ip source-route

!

!

ip cef

!

!

!

ip host R1 2000 192.168.0.1

ip host R2 2001 192.168.0.1

no ipv6 cef

multilink bundle-name authenticated

!

!

!

!

!

!

!

!

!

!

!

voice-card 0

!

crypto pki token default removal timeout 0

!

!

!

!

license udi pid CISCO2851 sn FTX1118A3AY

!

!

!

!

!

!

!

interface Loopback0

 ip address 192.168.0.1 255.255.255.0

!

interface GigabitEthernet0/0

 ip address 10.0.0.81 255.255.0.0

 duplex auto

 speed auto

!

interface GigabitEthernet0/1

 no ip address

 shutdown

 duplex auto

 speed auto

!

ip forward-protocol nd

!

no ip http server

no ip http secure-server

!

!

!

!

!

control-plane

!

!

!

!

mgcp profile default

!

!

!

!

!

line con 0

line aux 0

line 1/0 1/31

 transport input telnet

line vty 0 4

 exec-timeout 60 0

 password <removed>

 login

 transport input all

!

scheduler allocate 20000 1000

end

 

 

Comments

  • Hi,

     

    I edited out all the show commands you posted as they were unneeded and made the post way too long.  You issues is you are using 2000 plus the TTY line number in your ip host entries and it should be 2000 plus the router assigned line number which starts at 66 on this platform.

    Change your config to be,

     

    ip host R1 2066 192.168.0.1

    etc ..

    and it might solve some issues if you prevent access to the exec of the router by the remote device. Add "no exec" to your line 1/0 1/31 config section. 

     

     

  • That was it.  I should have seen it as the sh line command put it right there in front of me, however I was frantic (panic) and searched google for examples.  The problem is the examples are from 10-12 years ago and reflected a 2511 or 2600 series router with older software and the NM-16A



    Thanks MHughes
    image

    On Tue, Sep 20, 2016 at 8:49 AM, mhughes@ine.com <bounce-mhughesinecom@ieoc.com> wrote:

    Hi,

     

    I edited out all the show commands you posted as they were unneeded and made the post way too long.  You issues is you are using 2000 plus the TTY line number in your ip host entries and it should be 2000 plus the router assigned line number which starts at 66 on this platform.

    Change your config to be,

     

    ip host R1 2066 192.168.0.1

    etc ..

    and it might solve some issues if you prevent access to the exec of the router by the remote device. Add "no exec" to your line 1/0 1/31 config section. 

     

     




    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



Sign In or Register to comment.