CCIE Voice lab - RSVP configuraton - Error: not enough bandwidth

I configured CorpHQ, Branch1, & Branch2 with identical RSVP & MTP configurations in both the gateway & CUCM, however, when I attempt to make calls to/from Branch2, I get a NOT ENOUGH BANDWIDTH error. Calls beweeen CorpHQ & Branch1 work fine. On the CUCM, I configured REGIONS, DEVICE POOLS, LOCATIONS, SRST REFERENCES, MTPs, MRGs, and MRGLs for all 3 locations. Below is the configuration for all 3 gateways. 

 

Thanks,

 

BRANCH2#

interface Serial0/1/0.1 point-to-point

 description == FR To HQ

 ip address 177.0.201.2 255.255.255.0

 ip pim dense-mode

 snmp trap link-status

 frame-relay interface-dlci 102   

 ip rsvp bandwidth 136

!

sccp local Loopback0

sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1 

sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1 

sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1 

sccp

!

sccp ccm group 1

 bind interface Loopback0

 associate ccm 2 priority 1

 associate ccm 1 priority 2

 associate ccm 3 priority 3

 associate profile 1 register Br2-729-MTP

 associate profile 2 register Br2-711-MTP

!

dspfarm profile 1 mtp  

 codec g729ar8

 codec g729r8

 rsvp

 maximum sessions software 10

 associate application SCCP

!

dspfarm profile 2 mtp  

 codec g711ulaw

 rsvp

 maximum sessions software 10

 associate application SCCP

Comments

  • Sounds elementary, but are all the MTP registered in cucm?

    Sent from my iPhone

    On Sep 10, 2013, at 1:37 PM, rjferriolo <[email protected]> wrote:

    I configured CorpHQ, Branch1, & Branch2 with identical RSVP & MTP configurations in both the gateway & CUCM, however, when I attempt to make calls to/from Branch2, I get a NOT ENOUGH BANDWIDTH error. Calls beweeen CorpHQ & Branch1 work fine. On the CUCM, I configured REGIONS, DEVICE POOLS, LOCATIONS, SRST REFERENCES, MTPs, MRGs, and MRGLs for all 3 locations. Below is the configuration for all 3 gateways. 

     

    Thanks,

     

    BRANCH2#

    interface Serial0/1/0.1 point-to-point

     description == FR To HQ

     ip address 177.0.201.2 255.255.255.0

     ip pim dense-mode

     snmp trap link-status

     frame-relay interface-dlci 102   

     ip rsvp bandwidth 136

    !

    sccp local Loopback0

    sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1 

    sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1 

    sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1 

    sccp

    !

    sccp ccm group 1

     bind interface Loopback0

     associate ccm 2 priority 1

     associate ccm 1 priority 2

     associate ccm 3 priority 3

     associate profile 1 register Br2-729-MTP

     associate profile 2 register Br2-711-MTP

    !

    dspfarm profile 1 mtp  

     codec g729ar8

     codec g729r8

     rsvp

     maximum sessions software 10

     associate application SCCP

    !

    dspfarm profile 2 mtp  

     codec g711ulaw

     rsvp

     maximum sessions software 10

     associate application SCCP




    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx
  • This issue was resolved. 

     

    Thanks

  • Hi Michael:


    Yes, the MTPs were registered, however I had a typo in the rsvp bandwidth statement. Thanks for your feedback..


    Ron



    On Tue, Sep 10, 2013 at 5:10 PM, michael.thompson <[email protected]> wrote:
    Sounds elementary, but are all the MTP registered in cucm?

    Sent from my iPhone

    On Sep 10, 2013, at 1:37 PM, rjferriolo <[email protected]> wrote:


    I configured CorpHQ, Branch1, & Branch2 with identical RSVP & MTP configurations in both the gateway & CUCM, however, when I attempt to make calls to/from Branch2, I get a NOT ENOUGH BANDWIDTH error. Calls beweeen CorpHQ & Branch1 work fine. On the CUCM, I configured REGIONS, DEVICE POOLS, LOCATIONS, SRST REFERENCES, MTPs, MRGs, and MRGLs for all 3 locations. Below is the configuration for all 3 gateways. 

     

    Thanks,

     

    BRANCH2#

    interface Serial0/1/0.1 point-to-point

     description == FR To HQ

     ip address 177.0.201.2 255.255.255.0

     ip pim dense-mode

     snmp trap link-status

     frame-relay interface-dlci 102   

     ip rsvp bandwidth 136

    !

    sccp local Loopback0

    sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1 

    sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1 

    sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1 

    sccp

    !

    sccp ccm group 1

     bind interface Loopback0

     associate ccm 2 priority 1

     associate ccm 1 priority 2

     associate ccm 3 priority 3

     associate profile 1 register Br2-729-MTP

     associate profile 2 register Br2-711-MTP

    !

    dspfarm profile 1 mtp  

     codec g729ar8

     codec g729r8

     rsvp

     maximum sessions software 10

     associate application SCCP

    !

    dspfarm profile 2 mtp  

     codec g711ulaw

     rsvp

     maximum sessions software 10

     associate application SCCP




    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx



    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx

  • Hi Ron

    what you mean with "typo" ? :)

    Thank you

    Bye

  • Meaning my bandwidth statement going out to Branch2 was 36 instead of 136



    On Sat, Sep 14, 2013 at 3:06 AM, jryan77 <[email protected]> wrote:

    Hi Ron

    what you mean with "typo" ? :)

    Thank you

    Bye





    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx








  • Ah ok obviously ;-) thank u



    --- Messaggio originale ---



    Da: "rjferriolo" <[email protected]>

    Inviata: 14 settembre 2013 14:30

    A: [email protected]

    Oggetto: Re: [CCIE Voice] CCIE Voice lab - RSVP configuraton - Error: not enough bandwidth








    Meaning my bandwidth statement going out to Branch2 was 36 instead of 136






    On Sat, Sep 14, 2013 at 3:06 AM, jryan77 <[email protected]> wrote:

    Hi Ron

    what you mean with "typo" ? :)

    Thank you

    Bye








    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx












    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx



  • Thank you


    On Sat, Sep 14, 2013 at 8:49 AM, jryan77 <[email protected]> wrote:
    Ah ok obviously ;-) thank u



    --- Messaggio originale ---



    Da: "rjferriolo" <[email protected]>

    Inviata: 14 settembre 2013 14:30

    A: [email protected]

    Oggetto: Re: [CCIE Voice] CCIE Voice lab - RSVP configuraton - Error: not enough bandwidth








    Meaning my bandwidth statement going out to Branch2 was 36 instead of 136






    On Sat, Sep 14, 2013 at 3:06 AM, jryan77 <[email protected]> wrote:

    Hi Ron

    what you mean with "typo" ? :)

    Thank you

    Bye








    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx












    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx




    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com



    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx

Sign In or Register to comment.