Error loading config for PSTN V 3.5

 

PSTN(config-if)#interface Serial0/1:0

PSTN(config-if)#description == Frame-Relay Circuit to R1-HQ

PSTN(config-if)#frame-relay lmi-type ansi

                   ^

% Invalid input detected at '^' marker.

 

PSTN(config-if)#

---------------------------------------------------------------------------------------



PSTN uptime is 23 minutes

System returned to ROM by reload

System image file is "flash:c3725-adventerprisek9_ivs-mz.124-15.T13.bin"


----------------------------------------------------------------------------------------------------------



NAME: "Two port T1 voice interface daughtercard with Drop and Insert on Slot 0 SubSlot 0", DESCR: "Two port T1 voice interface daughtercard with Drop and Insert"

PID: VWIC-2MFT-T1-DI=  , VID: 1.0, SN: 29234000


NAME: "Two port E1 voice interface daughtercard with Drop and Insert on Slot 0 SubSlot 1", DESCR: "Two port E1 voice interface daughtercard with Drop and Insert"

PID: VWIC-2MFT-E1-DI=  , VID: 1.0, SN: 36906233


NAME: "Two port T1 voice interface daughtercard with Drop and Insert on Slot 0 SubSlot 2", DESCR: "Two port T1 voice interface daughtercard with Drop and Insert"

PID: VWIC-2MFT-T1-DI=  , VID: 1.0, SN: 30526228




 

Comments

  • Please issue the command 'encapsulation frame-relay' before you are going to configure LMI type of DLCI.

    HTH.


  • For the routers i saw up/up for frame-relay but for PSTN i see down/down.
    I can't ping between routers for the point to point.
    Is the load config file for workbook v 3.5 from the INE website incomplete? 
    it work fine for V3 but i'm having problem for v3.5 

     

    CorpHQ#sh frame-relay pvc
    DLCI = 201, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial0/0/1:0.2
    CorpHQ#

    -----------------------------------------------------------------------------------------------------------


    PSTN#sh frame-relay pvc

    PSTN#

    -----------------------------------------------------------------------------------------------
    controller T1 0/1

     framing esf

     clock source internal

     linecode b8zs

     cablelength short 133

     channel-group 0 timeslots 1-24 speed 64

     description == Data Circuit to CorpHQ

    !


    interface Serial0/1:0

     description == Frame-Relay Circuit to R1-HQ

     encapsulation frame-relay

     frame-relay lmi-type ansi

    !





  • I did make the T1 crossover myself and i see green lights on all the Vwic T1 and E1.
    I notice that if cables wasn't done right you will not see green lights but amber light?
    I have included a config of the following for the routers and pstn

    sh run | s Serial
    sh run | s controller 

    ------------------------------------------------------------------------------------------------------------------

    CorpHQ#sh run | s Serial

    interface Serial0/0/0:23

     no ip address

     encapsulation hdlc

     isdn switch-type primary-ni

     isdn incoming-voice voice

     isdn bind-l3 ccm-manager

     no cdp enable

    interface Serial0/0/1:0

     description == Frame-Relay Circuit to WAN

     no ip address

     encapsulation frame-relay

     no keepalive

     cdp enable

     no frame-relay inverse-arp

     frame-relay lmi-type ansi

    interface Serial0/0/1:0.1 point-to-point

     description == FR To BR1

     ip address 177.0.101.1 255.255.255.0

     snmp trap link-status

     frame-relay interface-dlci 101

    interface Serial0/0/1:0.2 point-to-point

     description == FR To BR2

     ip address 177.0.201.1 255.255.255.0

     ip pim dense-mode

     snmp trap link-status

     frame-relay interface-dlci 201

    CorpHQ#sh run | s controller

    controller T1 0/0/0

     framing esf

     linecode b8zs

     cablelength short 133

     pri-group timeslots 1-3,24 service mgcp

     description == Voice Circuit to PSTN

    controller T1 0/0/1

     framing esf

     linecode b8zs

     cablelength short 133

     channel-group 0 timeslots 1-24

     description == Data Circuit to WAN

    CorpHQ#

    --------------------------------------------------------------------------------------------------------------------------



    Branch1#sh run | s Serial

    interface Serial0/0/0:23

     no ip address

     encapsulation hdlc

     isdn switch-type primary-ni

     isdn incoming-voice voice

     isdn bind-l3 ccm-manager

     no cdp enable

    interface Serial0/0/1:0

     description == Frame-Relay Circuit to WAN

     no ip address

     encapsulation frame-relay

     no keepalive

     cdp enable

     no frame-relay inverse-arp

     frame-relay lmi-type ansi

    interface Serial0/0/1:0.1 point-to-point

     description == FR To HQ

     ip address 177.0.101.2 255.255.255.0

     snmp trap link-status

     frame-relay interface-dlci 101

    Branch1#sh run | s controller

    controller T1 0/0/0

     framing esf

     linecode b8zs

     cablelength short 133

     pri-group timeslots 1-3,24 service mgcp

     description == Voice Circuit to PSTN

    controller T1 0/0/1

     framing esf

     linecode b8zs

     cablelength short 133

     channel-group 0 timeslots 1-24

     description == Data Circuit to WAN

    Branch1#




    --------------------------------------------------------------------------------------------------------------------------------



    Branch2#sh run | s Serial

    interface Serial0/0/0:15

     no ip address

     encapsulation hdlc

     isdn switch-type primary-net5

     isdn incoming-voice voice

     isdn bind-l3 ccm-manager

     no cdp enable

    interface Serial0/0/1:0

     description == Frame-Relay Circuit to WAN

     no ip address

     encapsulation frame-relay

     no keepalive

     cdp enable

     no frame-relay inverse-arp

     frame-relay lmi-type ansi

    interface Serial0/0/1:0.1 point-to-point

     description == To HQ

     ip address 177.0.201.1 255.255.255.0

     ip pim dense-mode

     snmp trap link-status

     frame-relay interface-dlci 202

    Branch2#sh run | s controller

    controller E1 0/0/0

     pri-group timeslots 1-3,16 service mgcp

     description == Voice Circuit to PSTN

    controller E1 0/0/1

     channel-group 0 timeslots 1-31

     description == Data Circuit to WAN

    Branch2#





    -------------------------------------------------------------------------------------------------------------------------------




    PSTN#sh run | s Serial

    interface Serial0/0:23

     description == Voice PRI to CorpHQ

     no ip address

     encapsulation hdlc

     isdn switch-type primary-ni

     isdn protocol-emulate network

     isdn incoming-voice voice

     isdn map address transparent

     isdn supp-service name calling

     isdn negotiate-bchan resend-setup

     isdn outgoing ie network-facility

     isdn outgoing ie redirecting-number

     no cdp enable

    interface Serial0/1:0

     description == Frame-Relay Circuit to R1-HQ

     no ip address

     encapsulation frame-relay

     frame-relay lmi-type ansi

    interface Serial0/2:15

     description == Voice PRI to Branch2

     no ip address

     encapsulation hdlc

     isdn switch-type primary-net5

     isdn protocol-emulate network

     isdn incoming-voice voice

     isdn map address transparent

     isdn negotiate-bchan resend-setup

     isdn outgoing display-ie

     isdn outgoing ie redirecting-number

     no cdp enable

    interface Serial0/3:0

     description == Frame-Relay Circuit to R3-BR2

     no ip address

     encapsulation frame-relay

     frame-relay lmi-type ansi

    interface Serial0/4:23

     description == Voice PRI to Branch1

     no ip address

     encapsulation hdlc

     isdn switch-type primary-ni

     isdn protocol-emulate network

     isdn incoming-voice voice

     isdn map address transparent

     isdn supp-service name calling

     isdn negotiate-bchan resend-setup

     isdn outgoing ie network-facility

     isdn outgoing ie redirecting-number

     no cdp enable

    interface Serial0/5:0

     description == Frame-Relay Circuit to R2-BR1

     no ip address

     encapsulation frame-relay

     frame-relay lmi-type ansi

    PSTN#sh run | s controller

    controller T1 0/0

     framing esf

     clock source internal

     linecode b8zs

     cablelength short 133

     pri-group timeslots 1-3,24

     description == Voice Circuit to CorpHQ

    controller T1 0/1

     framing esf

     clock source internal

     linecode b8zs

     cablelength short 133

     channel-group 0 timeslots 1-24 speed 64

     description == Data Circuit to CorpHQ

    controller E1 0/2

     clock source internal

     pri-group timeslots 1-3,16

     description == Voice Circuit to Branch2

    controller E1 0/3

     clock source internal

     channel-group 0 timeslots 1-31

     description == Data Circuit to Branch2

    controller T1 0/4

     framing esf

     clock source internal

     linecode b8zs

     cablelength short 133

     pri-group timeslots 1-3,24

     description == Voice Circuit to Branch1

    controller T1 0/5

     framing esf

     clock source internal

     linecode b8zs

     cablelength short 133

     channel-group 0 timeslots 1-24 speed 64

     description == Data Circuit to Branch2

    controller E1 1/0

    controller E1 1/1

    PSTN#




  • Looks like your missing your frame-relay mappings. This is what I use on a 2821

     


    !

    interface Serial0/0/1:0

     description == Frame-Relay Circuit to R1-HQ

     no ip address

     encapsulation frame-relay

     cdp enable

     frame-relay lmi-type ansi

     frame-relay intf-type dce

     frame-relay route 101 interface Serial0/2/1:0 101

     frame-relay route 201 interface Serial0/1/1:0 201

    !

    interface Serial0/1/1:0

     description == Frame-Relay Circuit to R3-BR2

     no ip address

     encapsulation frame-relay

     cdp enable

     frame-relay lmi-type ansi

     frame-relay intf-type dce

     frame-relay route 201 interface Serial0/0/1:0 201

    !

    interface Serial0/2/1:0

     description == Frame-Relay Circuit to R2-BR1

     no ip address

     encapsulation frame-relay

     no fair-queue

     cdp enable

     frame-relay lmi-type ansi

     frame-relay intf-type dce

     frame-relay route 101 interface Serial0/0/1:0 101

    !

Sign In or Register to comment.