Gradedlabs.com - wrong config of the FRS?

markus.wirthmarkus.wirth
in CCIE Routing & Switching Technical

Hey guys!

I am configuring my GNS3 lab at the moment and took a look at the FR DLCI config.

Ahm...the PDF says that R6 has six DLCIs to the BB1???? What for? The DLCIs 51, 100, 101, 201, 301 and 401?

Is this an error of the sheet?

 

Here is the link to the PDF...page 4:  http://www.ine.com/l/rs_rrhs

 

Greetings!

 

· Share on FacebookShare on Twitter

Comments

  • Brian DennisBrian Dennis
    They connect to different sub-interfaces for different configurations used in the labs.

    interface Serial1/6
     description Connected to R6
     no ip address
     encapsulation frame-relay
     clock rate 64000
     frame-relay intf-type dce
    !
    interface Serial1/6.51 point-to-point
     description PVC 51 to R6
     ip address 54.1.3.254 255.255.255.0
     frame-relay interface-dlci 51   
    !
    interface Serial1/6.100 point-to-point
     description PVC 100 to R6
     ip address 54.1.2.254 255.255.255.0
     ipv6 address 2001:54:1:2::254/64
     ipv6 address FE80::254 link-local
     frame-relay interface-dlci 100   
    !
    interface Serial1/6.101 point-to-point
     description PVC 101 to R6
     ip address 54.1.1.254 255.255.255.0
     ip authentication mode eigrp 10 md5
     ip authentication key-chain eigrp 10 EIGRP
     ipv6 address 2001:54:254:1::254/64
     ipv6 address FE80::254 link-local
     ipv6 rip RIPng enable
     frame-relay interface-dlci 101   
    !
    interface Serial1/6.201 point-to-point
     description PPP over PVC 201 to R6
     frame-relay interface-dlci 201 ppp Virtual-Template1
    !
    interface Serial1/6.301 point-to-point
     description PPP over PVC 301 to R6
     frame-relay interface-dlci 301 ppp Virtual-Template11
    !         
    interface Serial1/6.401 point-to-point
     description Bridging over PVC 401 to R6
     frame-relay interface-dlci 401   
     bridge-group 1
    !

    Good luck with your studies!

    Brian Dennis, CCIEx5 #2210 (R&S/ISP-Dial/Security/SP/Voice)

    Internetwork Expert, Inc.


    From: zool85 <[email protected]>
    Reply-To: "[email protected]" <[email protected]>
    Date: Mon, 14 Nov 2011 14:35:33 -0600
    To: Brian Dennis <[email protected]>
    Subject: [CCIE R&S] Gradedlabs.com - wrong config of the FRS?

    Hey guys!

    I am configuring my GNS3 lab at the moment and took a look at the FR DLCI config.

    Ahm...the PDF says that R6 has six DLCIs to the BB1???? What for? The DLCIs 51, 100, 101, 201, 301 and 401?

    Is this an error of the sheet?

     

    Here is the link to the PDF...page 4:  http://www.ine.com/l/rs_rrhs

     

    Greetings!

     




    INE - The Industry Leader in CCIE Preparation

    http://www.INE.com


    Subscription information may be found at:

    http://www.ieoc.com/forums/ForumSubscriptions.aspx
    · Share on FacebookShare on Twitter
  • markus.wirthmarkus.wirth

    Thanks for the quick reply!!!

    that makes sense!

     

    Regards!

    · Share on FacebookShare on Twitter
Sign In or Register to comment.