Unable to Invoke Xcoder from CUBE

Have GK/CUBE function on the same box, all calls via GK/CUBE works fine until i hardcode codec on one of the dial-peer , as soon as i do call starts to fail with either way with fastbusy and can't get CUBE to invoke Xcoder

On the CUBE i've dspfarm configured & SCCP server with same source IP address

sccp local x.x.x.x & telephony-service ip source address x.x.x.x

have tried the above scenario only on INE/GradedLab Racks so far, i've noticed in other forums with resolution suggested as upgrading IOS fixed it , not sure if this is the case here.

document referred for this is http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_example09186a008092d6b3.shtml

only addition is GK on top of CUBE

 

 

 

 

Comments

  • Can you send us your CUBE and DSPFarm router config? (Full router config pls)

    Cheers,
    Mark


    On Oct 5, 2010, at 6:14 AM, Amit_Mehta wrote:

    Have GK/CUBE function on the same box, all calls via GK/CUBE works fine until i hardcode codec on one of the dial-peer , as soon as i do call starts to fail with either way with fastbusy and can't get CUBE to invoke Xcoder

    On the CUBE i've dspfarm configured & SCCP server with same source IP address

    sccp local x.x.x.x & telephony-service ip source address x.x.x.x

    have tried the above scenario only on INE/GradedLab Racks so far, i've noticed in other forums with resolution suggested as upgrading IOS fixed it , not sure if this is the case here.

    document referred for this is http://www.cisco.com/en/US/products/sw/voicesw/ps5640/products_configuration_example09186a008092d6b3.shtml

    only addition is GK on top of CUBE

     
     
     
     



    Internetwork Expert - The Industry Leader in CCIE Preparation
    http://www.internetworkexpert.com

    Subscription information may be found at:
    http://www.ieoc.com/forums/ForumSubscriptions.aspx

  • ok tried again with no luck have configs/debugs below

    IP Phone--SCCP--CUCM--GK_TRUNK--HQ-RTR(GK)--GK--BR1-RTR(GK/CUBE)---GK---BR2-RTR(GK)--CUCME--SCCP--CME Phone

    if i leave everything to default, call works fine from CME Phone to CUCM Phone , it takes 729 by default , can you tell why ?

    on BR1 Router if i hardcode dial-peer to 711ulaw call fails with fastbusy with the error message listed below along with config.

    HQ

    ==

    gatekeeper
     zone local CUCM cucm.cisco.com 177.1.254.1
     zone remote CUBE cube.cisco.com 177.1.254.2 1719
     zone prefix CUCM 1* gw-priority 9 HQ_GK_TRUNK_2
     zone prefix CUCM 1* gw-priority 5 HQ_GK_TRUNK_1
     zone prefix CUBE 44*
     gw-type-prefix 4#* hopoff CUBE
     no shutdown

    BR1

    ==

    voice translation-rule 3
     rule 1 /^4#(4423*)/ /2#1/
    !
    voice translation-rule 4
     rule 1 /^4#(1775.......)/ /1#1/
    !
    voice translation-rule 5
     rule 1 /^4#(1312.......)/ /1#1/
    !
    !

    !
    voice translation-profile TO_BR1
     translate called 5
    !
    voice translation-profile TO_BR2
     translate called 3
    !
    voice translation-profile TO_HQ
     translate called 4
    !
    !
    voice-card 0
     Dsp services dspfarm

    interface Loopback0
     ip address 177.1.254.2 255.255.255.255
     h323-gateway voip interface
     h323-gateway voip id CUBE ipaddr 177.1.254.2 1719
     h323-gateway voip h323-id BR1_IPIPGW
     h323-gateway voip tech-prefix 4#
     h323-gateway voip bind srcaddr 177.1.254.2
    !

    interface Vlan11
     description == Voice VLAN
     ip address 177.2.11.1 255.255.255.0
     no autostate

    sccp local Vlan11
    sccp ccm 177.2.11.1 identifier 1 version 7.0
    sccp ip precedence 3
    sccp
    !
    sccp ccm group 1
     associate ccm 1 priority 1
     associate profile 1 register MTP001563c2e780
    !
     dspfarm profile 1 transcode 
     codec g711ulaw
     codec g711alaw
     codec g729ar8
     codec g729abr8
     codec g729r8
     maximum sessions 2
     associate application SCCP
    !
     dial-peer voice 3000 voip
     description TO_BR2
     translation-profile incoming TO_BR2
     destination-pattern 2#4423........$
     session target ras
     incoming called-number 4#4423........$
    !
    dial-peer voice 1000 voip
     description TO_HQ
     translation-profile incoming TO_HQ
     destination-pattern 1#1775.......$
     session target ras
     incoming called-number 4#1775.......$
     codec g711ulaw
    !
    dial-peer voice 2000 voip
     description TO_BR1
     translation-profile incoming TO_BR1
     destination-pattern 1#1312.......$
     session target ras
     incoming called-number 4#1312.......$

    gatekeeper
     zone local CUBE cube.cisco.com 177.1.254.2
     zone remote CUCM cucm.cisco.com 177.1.254.1 1719
     zone remote CUCME cucme.cisco.com 177.1.254.3 1719 invia CUBE outvia CUBE
     zone prefix CUCM 1*
     zone prefix CUCME 44*
     gw-type-prefix 2#* hopoff CUCME
     gw-type-prefix 1#* hopoff CUCM
     no shutdown
    !
    !
    telephony-service
     sdspfarm units 1
     sdspfarm transcode sessions 2
     sdspfarm tag 1 MTP001563c2e780
     max-ephones 10
     max-dn 10
     ip source-address 177.2.12.1 port 2000
     max-conferences 8 gain -6
     transfer-system full-consult
     create cnf-files version-stamp 7960 Oct 12 2010 12:49:23

     

    BR2

    ===


    voice translation-rule 5
     rule 1 /^2#44232131(....)$/ /1/
     rule 2 /^2#4423(........)$/ /91/
    !
    voice translation-rule 6
     rule 1 /^900(1775.......)/ /4#1/
    !
    voice translation-rule 7
     rule 1 /^900(1312.......)/ /4#1/
    !
    !

    voice translation-profile TO_BR1
     translate called 7
    !
    voice translation-profile TO_BR2
     translate called 5
    !
    voice translation-profile TO_HQ
     translate called 6
    !
    !
     
    interface Loopback0
     ip address 177.1.254.3 255.255.255.255
     h323-gateway voip interface
     h323-gateway voip id CUCME ipaddr 177.1.254.3 1719
     h323-gateway voip h323-id BR2_GW
     h323-gateway voip tech-prefix 2#
     h323-gateway voip bind srcaddr 177.1.254.3
     
    dial-peer voice 3000 voip
     description TO_BR2
     translation-profile incoming TO_BR2
     session target ras
     incoming called-number 2#4423........$
    !
    dial-peer voice 1000 voip
     description TO_HQ_and_TEHO
     translation-profile outgoing TO_HQ
     destination-pattern 9001775.......$
     session target ras

    dial-peer voice 2000 voip
     description TO_BR1_and_TEHO
     translation-profile outgoing TO_BR1
     destination-pattern 9001312.......$
     session target ras

    gatekeeper
     zone local CUCME cucme.cisco.com 177.1.254.3
     zone remote CUBE cube.cisco.com 177.1.254.2 1719
     zone prefix CUBE 1*
     zone prefix CUCME 44*
     gw-type-prefix 4#* hopoff CUBE
     no shutdown
    !
    !
    telephony-service
     max-ephones 40
     max-dn 40
     ip source-address 177.3.11.1 port 2000
     time-format 24
     date-format dd-mm-yy
     max-conferences 8 gain -6
     dn-webedit
     time-webedit
     transfer-system full-consult
     create cnf-files version-stamp 7960 Oct 12 2010 09:12:54
    !
    !
    ephone-dn  1  dual-line
     number 3001 no-reg primary
     label BR2 IP PH 1
     description +442321313001
     name BR2 IP PH 1
    !
    !
    ephone-dn  2  dual-line
     number 3002 no-reg primary
     label BR2 IP PH 2
     description +442321313002
     name BR2 IP PH 2
    !
    !
    ephone  1
     device-security-mode none
     mac-address 0016.4680.7081
     button  1:2
    !
    ephone  2
     device-security-mode none
     mac-address 0019.560C.940D
     button  1:1
         

    LOGS BR1, where call fails

     

     12:53:23.886: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: QUEUE_EVENT (minor 0) wakeup
    BR1-R2#
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: QUEUE_EVENT (minor 0) wakeup
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: (4#17752011001) Matched tech-prefix 4#
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: (4#17752011001) Matched zone-prefix 1
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: checking the source of the LRQ. source_endptp=0x0
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: srcvia found gkname of source zone. looking up CUCME in zo            ne list
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: about to check the source side, src_zonep=0x49791758
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: matched zone is CUCME
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq      and z_invianamelen=4
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq      and z_invianamep=CUBE
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq(CUCME): Terminating inbound call at the IPIPGW in zone CUBE
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: zonep: 0x49F2F6C4, tpp: 0x49A31870, current_e            ndpt: 1
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Selecting IPIPGW based on tech prefix. qelemp            .head=0x497F95F4, use_count=1, current_endpt=1
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Ga
    BR1-R2#teway selection will start at the top of the linked list. use_count=1, current_endpt=0
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: qelemp=0x497F95F4, loop_count=0
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Examining tgwp 0x47DCA984, g_supp_prots: 0x50             qelemp: 0x497F95F4, loop_count: 1
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Found an IPIPGW. tgwp: 0x47DCA984, endptsigIP            : 177.1.254.2, endptrasIP: 177.1.254.2, zone: CUBE
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Selected an IPIPGW.
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_zone_get_proxy_usage: local zone= CUBE, remote zone= CUCME, call direc            tion= 0, eptype= 67650 be_entry= 0
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_zone_get_proxy_usage: returns proxied = 0
    Oct 12 12:53:25.962: //89/8813039680BA/H323/setu
    BR1-R2#p_ind: Receive bearer cap infoXRate 16, rateMult 0
    Oct 12 12:53:25.966: //89/8813039680BA/H323/cch323_fastStart_codec_match: ccb->remote_fastStart=0x4A3BFCCC
    Oct 12 12:53:25.966: //89/8813039680BA/H323/cch323_fastStart_codec_match: symm_mask=4, tempOtherCodec=16, templocalCodec=16,             audioFastStartArray=0x4984601C
    Oct 12 12:53:25.966: //89/8813039680BA/H323/cch323_fastStart_codec_match: Setting local audio_cap_mask
    Oct 12 12:53:25.966: //89/8813039680BA/H323/cch323_fastStart_codec_match: Inbound legs state_mc_mode=0x10F
    Oct 12 12:53:25.966: //89/8813039680BA/H323/cch323_fastStart_codec_match: Executing legacy code
    Oct 12 12:53:25.966: //89/8813039680BA/H323/cch323_set_h245_state_mc_mode_incoming: h245 state m/c mode=0x10F, h323_ctl=0x2F
    Oct 12 12:53:25.974: //89/8813039680BA/H323/cch323_call_generic_cleanup: De-allocating audioFastStartArray.

     

     

     

     

     

     

     







  • Don’t know if Josh, Mark or anyone else has an answer, but I think we need
    to see what your configuration on the CUCM is like. Try to have in mind which
    device needs the transcoder. Where is the actual transcoding needed?

    For the phone? Trunk or GW?

     

    lawedo



     


    From: Amit_Mehta

    Sent: Wednesday, October 13, 2010 4:47 PM


    Subject: Re: [CCIE Voice] Unable to Invoke Xcoder from
    CUBE

     

    ok tried again with no luck have configs/debugs below

    IP
    Phone--SCCP--CUCM--GK_TRUNK--HQ-RTR(GK)--GK--BR1-RTR(GK/CUBE)---GK---BR2-RTR(GK)--CUCME--SCCP--CME
    Phone

    if i leave everything to default, call works fine from CME Phone to CUCM
    Phone , it takes 729 by default , can you tell why ?

    on BR1 Router if i hardcode dial-peer to 711ulaw call fails with fastbusy
    with the error message listed below along with config.

    HQ

    ==

    gatekeeper
    zone local CUCM cucm.cisco.com 177.1.254.1
    zone remote CUBE
    cube.cisco.com 177.1.254.2 1719
    zone prefix CUCM 1* gw-priority 9
    HQ_GK_TRUNK_2
    zone prefix CUCM 1* gw-priority 5 HQ_GK_TRUNK_1
    zone prefix
    CUBE 44*
    gw-type-prefix 4#* hopoff CUBE
    no shutdown

    BR1

    ==

    voice translation-rule 3
    rule 1 /^4#(4423*)/ /2#1/
    !
    voice
    translation-rule 4
    rule 1 /^4#(1775.......)/ /1#1/
    !
    voice
    translation-rule 5
    rule 1 /^4#(1312.......)/ /1#1/
    !
    !

    !
    voice translation-profile TO_BR1
    translate called 5
    !
    voice
    translation-profile TO_BR2
    translate called 3
    !
    voice
    translation-profile TO_HQ
    translate called 4
    !
    !
    voice-card 0
    Dsp
    services dspfarm

    interface Loopback0
    ip address 177.1.254.2 255.255.255.255
    h323-gateway
    voip interface
    h323-gateway voip id CUBE ipaddr 177.1.254.2
    1719
    h323-gateway voip h323-id BR1_IPIPGW
    h323-gateway voip tech-prefix
    4#
    h323-gateway voip bind srcaddr 177.1.254.2
    !

    interface Vlan11
    description == Voice VLAN
    ip address 177.2.11.1
    255.255.255.0
    no autostate

    sccp local Vlan11
    sccp ccm 177.2.11.1 identifier 1 version 7.0
    sccp ip
    precedence 3
    sccp
    !
    sccp ccm group 1
    associate ccm 1 priority
    1
    associate profile 1 register MTP001563c2e780
    !
    dspfarm profile 1
    transcode 
    codec g711ulaw
    codec g711alaw
    codec g729ar8
    codec
    g729abr8
    codec g729r8
    maximum sessions 2
    associate application
    SCCP
    !
    dial-peer voice 3000 voip
    description
    TO_BR2
    translation-profile incoming TO_BR2
    destination-pattern
    2#4423........$
    session target ras
    incoming called-number
    4#4423........$
    !
    dial-peer voice 1000 voip
    description
    TO_HQ
    translation-profile incoming TO_HQ
    destination-pattern
    1#1775.......$
    session target ras
    incoming called-number
    4#1775.......$
    codec g711ulaw
    !
    dial-peer voice 2000
    voip
    description TO_BR1
    translation-profile incoming
    TO_BR1
    destination-pattern 1#1312.......$
    session target ras
    incoming
    called-number 4#1312.......$

    gatekeeper
    zone local CUBE cube.cisco.com 177.1.254.2
    zone remote CUCM
    cucm.cisco.com 177.1.254.1 1719
    zone remote CUCME cucme.cisco.com 177.1.254.3
    1719 invia CUBE outvia CUBE
    zone prefix CUCM 1*
    zone prefix CUCME
    44*
    gw-type-prefix 2#* hopoff CUCME
    gw-type-prefix 1#* hopoff CUCM
    no
    shutdown
    !
    !
    telephony-service
    sdspfarm units 1
    sdspfarm
    transcode sessions 2
    sdspfarm tag 1 MTP001563c2e780
    max-ephones
    10
    max-dn 10
    ip source-address 177.2.12.1 port 2000
    max-conferences 8
    gain -6
    transfer-system full-consult
    create cnf-files version-stamp 7960
    Oct 12 2010 12:49:23

     

    BR2

    ===


    voice translation-rule 5
    rule 1 /^2#44232131(....)$/ /1/
    rule 2
    /^2#4423(........)$/ /91/
    !
    voice translation-rule 6
    rule 1
    /^900(1775.......)/ /4#1/
    !
    voice translation-rule 7
    rule 1
    /^900(1312.......)/ /4#1/
    !
    !

    voice translation-profile TO_BR1
    translate called 7
    !
    voice
    translation-profile TO_BR2
    translate called 5
    !
    voice
    translation-profile TO_HQ
    translate called 6
    !
    !
     
    interface
    Loopback0
    ip address 177.1.254.3 255.255.255.255
    h323-gateway voip
    interface
    h323-gateway voip id CUCME ipaddr 177.1.254.3 1719
    h323-gateway
    voip h323-id BR2_GW
    h323-gateway voip tech-prefix 2#
    h323-gateway voip
    bind srcaddr 177.1.254.3
     
    dial-peer voice 3000 voip
    description
    TO_BR2
    translation-profile incoming TO_BR2
    session target ras
    incoming
    called-number 2#4423........$
    !
    dial-peer voice 1000 voip
    description
    TO_HQ_and_TEHO
    translation-profile outgoing TO_HQ
    destination-pattern
    9001775.......$
    session target ras

    dial-peer voice 2000 voip
    description
    TO_BR1_and_TEHO
    translation-profile outgoing TO_BR1
    destination-pattern
    9001312.......$
    session target ras

    gatekeeper
    zone local CUCME cucme.cisco.com 177.1.254.3
    zone remote
    CUBE cube.cisco.com 177.1.254.2 1719
    zone prefix CUBE 1*
    zone prefix CUCME
    44*
    gw-type-prefix 4#* hopoff CUBE
    no
    shutdown
    !
    !
    telephony-service
    max-ephones 40
    max-dn 40
    ip
    source-address 177.3.11.1 port 2000
    time-format 24
    date-format
    dd-mm-yy
    max-conferences 8 gain -6
    dn-webedit
    time-webedit

    transfer-system full-consult
    create cnf-files version-stamp 7960 Oct 12
    2010 09:12:54
    !
    !
    ephone-dn  1  dual-line
    number 3001
    no-reg primary
    label BR2 IP PH 1
    description +442321313001
    name BR2 IP
    PH 1
    !
    !
    ephone-dn  2  dual-line
    number 3002 no-reg
    primary
    label BR2 IP PH 2
    description +442321313002
    name BR2 IP PH
    2
    !
    !
    ephone  1
    device-security-mode none
    mac-address
    0016.4680.7081
    button  1:2
    !
    ephone 
    2
    device-security-mode none
    mac-address 0019.560C.940D
    button 
    1:1
         

    LOGS BR1, where call fails

     

    12:53:23.886: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: QUEUE_EVENT (minor
    0) wakeup
    BR1-R2#
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_process: QUEUE_EVENT (minor 0) wakeup
    Oct
    12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: (4#17752011001)
    Matched tech-prefix 4#
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: (4#17752011001) Matched
    zone-prefix 1
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: checking the source of the LRQ.
    source_endptp=0x0
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: srcvia found gkname of source
    zone. looking up CUCME in
    zo            ne
    list
    Oct 12 12:53:25.930: //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: about
    to check the source side, src_zonep=0x49791758
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq: matched zone is CUCME
    Oct 12
    12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq      and
    z_invianamelen=4
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq      and
    z_invianamep=CUBE
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_rassrv_lrq(CUCME): Terminating inbound call at
    the IPIPGW in zone CUBE
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: zonep: 0x49F2F6C4,
    tpp: 0x49A31870,
    current_e           
    ndpt: 1
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Selecting IPIPGW
    based on tech prefix.
    qelemp           
    .head=0x497F95F4, use_count=1, current_endpt=1
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Ga
    BR1-R2#teway
    selection will start at the top of the linked list. use_count=1,
    current_endpt=0
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: qelemp=0x497F95F4,
    loop_count=0
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Examining tgwp
    0x47DCA984, g_supp_prots:
    0x50            
    qelemp: 0x497F95F4, loop_count: 1
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Found an IPIPGW.
    tgwp: 0x47DCA984,
    endptsigIP            :
    177.1.254.2, endptrasIP: 177.1.254.2, zone: CUBE
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_gw_select_ipipgw_random: Selected an
    IPIPGW.
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_zone_get_proxy_usage: local zone= CUBE, remote
    zone= CUCME, call
    direc            tion= 0,
    eptype= 67650 be_entry= 0
    Oct 12 12:53:25.930:
    //xxxxxxxxxxxx/xxxxxxxxxxxx/GK/gk_zone_get_proxy_usage: returns proxied =
    0
    Oct 12 12:53:25.962: //89/8813039680BA/H323/setu
    BR1-R2#p_ind: Receive
    bearer cap infoXRate 16, rateMult 0
    Oct 12 12:53:25.966:
    //89/8813039680BA/H323/cch323_fastStart_codec_match:
    ccb->remote_fastStart=0x4A3BFCCC
    Oct 12 12:53:25.966:
    //89/8813039680BA/H323/cch323_fastStart_codec_match: symm_mask=4,
    tempOtherCodec=16,
    templocalCodec=16,            
    audioFastStartArray=0x4984601C
    Oct 12 12:53:25.966:
    //89/8813039680BA/H323/cch323_fastStart_codec_match: Setting local
    audio_cap_mask
    Oct 12 12:53:25.966:
    //89/8813039680BA/H323/cch323_fastStart_codec_match: Inbound legs
    state_mc_mode=0x10F
    Oct 12 12:53:25.966:
    //89/8813039680BA/H323/cch323_fastStart_codec_match: Executing legacy
    code
    Oct 12 12:53:25.966:
    //89/8813039680BA/H323/cch323_set_h245_state_mc_mode_incoming: h245 state m/c
    mode=0x10F, h323_ctl=0x2F
    Oct 12 12:53:25.974:
    //89/8813039680BA/H323/cch323_call_generic_cleanup: De-allocating
    audioFastStartArray.

     

     

     

     

     

     

     




    Internetwork
    Expert - The Industry Leader in CCIE
    Preparation
    http://www.internetworkexpert.com

    Subscription information
    may be found
    at:
    http://www.ieoc.com/forums/ForumSubscriptions.aspx
  • Another box ticked, don't know what was i doing wrong before, however can get this to work just fine now, with or w/o GK in picture. Pheww...

     

Sign In or Register to comment.