-
hi im trying some netflow out for IPV6 - and its a bit atchy, I noticed on the forum that 12.4 only owrks for netflow ipv6 in the old syntax i.e. ipv6 flow-cache on pre 12.4.(20) and after that it is flexible netflow. Normal 0 false false false EN-GB X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name
-
So im sitting here looking at a nat secnario to get the connectivity then realised there is a bnat question at the end - solving this ... ignore me ...
-
greeting, if this is the case then the community setting should be local-as not no-export, which in turn you cannot get full reachability to the BB routes as they cannot (have not got) routes to the 156.5.0.0 subnet. I belive the question should say "should not be advertised out from as54" hence making the Sg correct and allowing full connectivity
-
Hello again, THis should be set on a per peer in as 100 as if left to for all peers as the SG solution does it will change the timers for the bb1 and bb3 sessions also. i.e. router bgp 100 no synchronization bgp router-id 150.5.3.3 bgp log-neighbor-changes neighbor 156.5.136.1 remote-as 100 neighbor 156.5.136.1 timers 1 3 neighbor 156.5.136.6 remote
-
hi There, this solution is incorrect as it leaves the area 5,57 routes in .. also the verification on the SG is on sw3 not bb2 ,..? this lab is all over the place...:-( RS.5.5.BB2>sh ip rou ospf 156.5.0.0/16 is variably subnetted, 5 subnets, 3 masks O IA 156.5.0.0/16 [110/10] via 192.10.5.2, 00:02:03, Ethernet0 O IA 156.5.5.0/24 [110/2019] via 192
-
Hi ALL, MY Rack5R4(config)#do sh fram pvc 100 PVC Statistics for interface Serial0/1/0 (Frame Relay DTE) DLCI = 100, DLCI USAGE = LOCAL, PVC STATUS = STATIC, INTERFACE = Serial0/1/0 input pkts 1144 output pkts 969 in bytes 40308 out bytes 39238 dropped pkts 0 in pkts dropped 0 out pkts dropped 0 out bytes dropped 0 in FECN pkts 0 in BECN pkts 0 out
-
Ah another revist to cat qos ... the answer is 10 .. why ? 2) When configured in shaped mode, bandwidth restriction (policing) for each queue is based on inverse absolute weight. E.g. for “srr-queue bandwidth shape 30 0 0 0” we effectively restrict the first queue to “1/30” of the interface bandwidth (which is approximately 3
-
Hi, I got from this to configure on r1 not r5..? the configis valid - would this get points in the lab as it does not specify R5..? thanks, Lee
-
Hi there, Well here bgp bestpath is not supported - but I found alternative though... Rack5R5(config-router)#bgp bestpath ? compare-routerid Compare router-id for identical EBGP paths cost-community cost community med MED attribute Rack5R5(config-router)#bgp bestpath Also looking at the SG the weight is not set to 300 but it is the as path - this looks
-
Hi there, Ive noticed the demand-circuit is only configured on one link, should we put it on both..? I have tried both and it just removes the Configured as demand circuit. attribute of the sh ip osp int command..? interface Serial0/1/0 ip address 176.5.45.4 255.255.255.0 encapsulation ppp ip ospf demand-circuit ipv6 address FE80::4 link-local ipv6