in
IEOC CCIE Forums

IEOC - INE's Online Community

Welcome to INE's Online Community - IEOC - a place for CCIE and CCENT candidates to connect, share, and learn. Our Online Community features CCIE forums and discussions for all tracks including Routing & Switching, Voice, Security, Service Provider, Wireless,, and Storage. Through these online communities you can discuss your questions with thousands of your peers, hundreds of CCIE's and INE's own team of world renowned CCIE instructors and authors, Brian Dennis - Quintuple CCIE #2210, Brian McGahan – Triple CCIE #8593, Petr Lapukhov - Quad CCIE #16379, and Mark Snow - Dual CCIE #14073.
Latest post 08-18-2016 11:32 AM by OliDrouin. 4 replies.
Page 1 of 1 (5 items)
Sort Posts: Previous Next
  • 06-20-2016 12:57 PM

    Full Lab 1, Section 1.2

    Hi there,

    I've just sarted with the workbook but having difficulty with 1.2, after configuring each device I can't seem to ping router 4 from router 3.

    Pinging router 2 from router one works without issue. Initally I was having difficulty with the diagram but found the physical topology here on the forum. I recabled the topology but 3 times I'v started fresh now I can't get it to work. I Have checked over and over aging and my configuration is exactly as the workbook states.. so is it my physical topology thats the issue ??

     

    • Post Points: 20
  • 06-21-2016 8:22 PM In reply to

    Re: Full Lab 1, Section 1.2

    maybe it's too soon for ping test; u are in section 1 which usually is L2 stuff (don't have wb at the moment).  if those are L3 switches, u need routing before pinging.  I would keep going, do more sections like L3 routing unless task says do ping test now.

     

    • Post Points: 20
  • 06-27-2016 4:25 AM In reply to

    Re: Full Lab 1, Section 1.2

    Hi Martinl, it does say to do ping tests in that section of the workbook? I have tried it on Boson 10 and on packet tracer and on both sims I can ping router 2 from router 1 but not router 4 from router 3. This leads me to believe that there may be an error in the workbook.

     

    I'm looking for somebody to go as far as section 1.2 and see if they are getting the same issues with the ping ? Its very hard for me to continue if the network is not working at this early stage??

    Wes.

    • Post Points: 35
  • 06-27-2016 2:41 PM In reply to

    Re: Full Lab 1, Section 1.2

    Sorry, I thought this is ccie rs lab.  check cdp, check trunks and vlans (probably vlans are missing or/and trunks); 

    since your pt works, compare pt to ine lab.

    there were some other posts about ccna wb, search this forum

    • Post Points: 5
  • 08-18-2016 11:32 AM In reply to

    Re: Full Lab 1, Section 1.2

    Howdy!

              I completed the tasks yesterday, I will have to redo this lab so I have a better grasp of what is  really happening. I noticed that there are some inconsistencies between the topology/workbook and what is really going on. For example the spanning-tree election result was different in the rack I had (i.e.: 14) than what I was expecting to see according to the workbook.

     

    Regarding your problem: make sure you apply 'no ip routing' on R2/R3/R4 like the answer section specifies or else it will not ping. I'm not in front of the lab right now but if my memory is correct you want R2/R3/R4 to behave as host at this stage.

     

     

    • Post Points: 5
Page 1 of 1 (5 items)
IEOC CCIE Forums Internetwork Expert CCIE Training
About IEOC | Terms of Use | RSS | Privacy Policy
© 2010 Internetwork Expert, Inc. All Rights Reserved